Wirtgen milling machines

The power package is not only ideally suited to comply with legal provisions regarding the maximum total weight of oversize transports but with its milling performance of 900 tonnes per hour also fully meets the high performance requirements of milling contractors. WIDIRVE machine managment system, which greatly improves operator comfort, electronic ISC travel drive control, PTS system (short for "parallel to surface") and a choice of three different milling drum speeds.

Find out about the components of WIRTGEN large milling machines

1. Electrical system

   • Emergency operation
     Electrohydraulic power pack to raise machine in emergency mode.
   • Camera system
     Robust camera system including up to six cameras and up to two screens.
   • Job data
     Precise recording of job data including “truck full” message.

   Additional Information

2. Traction drive

   • Hydraulic pre-tensioning of track chains
     Hydraulically pre-tensioned track chains for optimized operation.
   • Traction control
     Intelligent electronic traction control system for the track units.
   • Track speed adjustment
     Electronic adjustment of the track speed during cornering to ensure maximum traction and low wear and tear.
   • Four-fold full-floating axle
     Four-fold full-floating axle for optimum machine stability.

3. Operator's platform

   • Multifunctional joystick
     Multifunctional joystick with driving, steering, selecting operating mode, raising machine and switching off conveyor functions.
   • Ergonomics
     Ergonomically designed, backlit controls for non-tiring, productive working.
   • Hydraulically moving and swivelling operator’s cabin
     Optionally available Operator Comfort System (OCS) for an ideal working environment.
   • Protective canopy
     Fixed protective canopy with telescoping side panels for maximum protection from inclement weather.
   • Parallel alignment of machine
     Automatic parallel alignment of the machine both during the milling operation and in transport mode.

   Additional Information

4. Milling drum unit

   • Locking of scraper blade
     Automatic mechanical locking of scraper blade to ensure ease of operation.
   • FCS LIGHT
     FCS Light for the quick replacement of milling drums in FB2000 and FB2200 milling drum units.
   • HT22 quick-change toolholder system
     Extra efficient, tried-and-tested HT22 quick-change toolholder system as standard equipment.
   • Right-hand side plate lift of 450 mm
     Right-hand side plate can be raised by up to 450 mm to allow flush-to-kerb milling at the full milling depth.
   • Load-controlled water spray system
     Water spray system with automatic adjustment to the milling performance for optimum tool cooling.
   • Milling drum turning device
     Drum turning device to enable cutting tool replacement with the diesel engine switched off.

5. Engine station

   • Three different milling drum speed options
     Three selectable cutting speeds for optimum millingperformance in a broad range of applications.
   • Load-controlled fan speed
     Fan speed governed by engine temperature for low energy consumption and low noise emission levels.

   Additional Information

6. Conveyor system

   • Large slewing angles
     Conveyor slewing angles of 60° to both sides to optimize the loading process.
   • Tremendous conveying capacity
     High conveyor loading capacity and drive power for highly effcient material loading.
   • Vacuum Cutting System
     Vacuum Cutting System for improved visibility.
   • Folding conveyor with locking mechanism
     Folding conveyor with intelligent mechanical locking mechanism for easy transport.

7. Machine frame

   • Perfect visibility
     Slender machine frame design at the front including dual wasp waist for a perfect view of the milling edge.
   • Ease of transport
     Ease of transport due to low machine weight and variable supplementary weights of up to 1, 700 kg.

8. Levelling

   • Large choice of sensors
     LEVEL PRO automatic levelling system as standard equipment, offering a large choice of sensors and highly precise control of the milling depth.
   • Milling depth indicator
     Milling depth indicator on the LEVEL PRO screen (showing difference between scraper blade and side plate positions).
   • Scanning in front of the milling drum
     Scanning in front of the milling drum via hydraulic cylinders with integrated measuring system – suitable for use also with the Multiplex system.
   • Automatic system to initiate the milling process
     Automatic system to initiate the milling process with load-controlled lowering speed.

   Additional Information

Detailed information about the W 220

Cold milling machine W 200 / W 200i

Compact 2-m machine for efficient milling jobs

Cold milling machine W 200 Hi

Compact large milling machine for dual flush-to-kerb milling

Cold milling machine W 210 / W 210i

Versatile high-performance milling machine for professional applications